Product Inquiry BLOG » Driveway Cleaners

Will Pour-N-Restore discolor concrete or masonry?

Meccanator — Fri, 30 Oct 2009 17:23:09 +0000

Pour-N-Restore has been tested on various materials without discolorationl. Furthermore, we have not heard of a customer complaint about discoloration. It is always recommend however, that you first test a small inconspicuous area before treating painted, stained, or pigmented surfaces.

Can I use Pour-N-Restore on asphalt or blacktop?

Meccanator — Fri, 30 Oct 2009 17:22:33 +0000

If Pour-N-Restore is used to remove stains on asphalt it will dissolve the surface layer and expose the aggregate. Therefore, we do not recommend it for stain removal on asphalt. However, Pour-N-Restore can be used to remove stains from asphalt on concrete or masonry surfaces.

Will Pour-N-Restore bleach concrete or masonry?

Meccanator — Fri, 30 Oct 2009 17:21:35 +0000

No. Pour-N-Restore does not bleach. If after using Pour-N-Restore you find that the area appears lighter in color, simply rinse the area with a strong stream of water to flush the white absorbent powder from the surface.

Why is Pour-N-Restore taking so long to dry?

Meccanator — Fri, 30 Oct 2009 16:49:35 +0000

At temperatures above 60°F (16°C), dry time will be approximately 5-8 hours. If you are using Pour-N-Restore in cooler temperatures, expect dry time to be extended considerably. Dry time can also be extended by high levels of humidity and poor ventilation. To accelerate dry time, spread Pour-N-Restore with our v-notch spreader and/or direct a fan at the treated area.

After sweeping up Pour-N-Restore, why does the area still appear dark?

Meccanator — Fri, 30 Oct 2009 16:48:21 +0000

After sweeping Pour-N-Restore, there will be moisture trapped in the pores of the concrete or masonry surface. Simply provide adequate ventilation and allow the moisture to evaporate out.

Can I use Pour-N-Restore on sealed surfaces?

Meccanator — Fri, 30 Oct 2009 16:47:55 +0000

While Pour-N-Restore is effective on sealed surfaces, dry time may be extended considerably in some cases. After sweeping Pour-N-Restore, it may take several days, even weeks, for the moisture to evaporate out from beneath some sealers. To increase the evaporation rate, provide maximum ventilation and direct a fan at the treated area.

Will Pour-N-Restore harm grass or plants?

Meccanator — Fri, 30 Oct 2009 16:47:18 +0000

After it dries to a powder, Pour-N-Restore will not harm vegetation. However, in its liquid state, it will be harmful. Therefore, if Pour-N-Restore comes in contact with vegetation, dilute it with large amounts of water.

Does scrubbing Pour-N-Restore improve performance?

Meccanator — Wed, 28 Oct 2009 17:15:06 +0000

Scrubbing is not recommended on the first application since it may actually hinder performance. However, if a stubborn stain requires subsequent applications, scrubbing may enhance performance. Scrubbing is particularly helpful on heavy stains left from materials like tar and wax.

Does Pour-N-Restore work on old stains?

Meccanator — Wed, 28 Oct 2009 17:14:24 +0000

Yes. Pour-N-Restore is effective on old stains too. If the stain has not been cleaned previously with other cleaning products, one application should be sufficient. If subsequent applications are required, scrubbing may enhance performance.

How do I remove Pour-N-Restore if it gets embedded in the sealer?

Meccanator — Wed, 28 Oct 2009 17:13:44 +0000

Pour-N-Restore can adversely affect some sealers leaving a white residue, shiny residue, or powder embedded in the sealer. The solution is to strip the sealer with more Pour-N-Restore. Apply it to the affected area; let it soak for 10-15 minutes, and scrub. After 30 minutes, scrub again, and then sponge Pour-N-Restore from the surface, or rinse, to remove the sealer. When the surface is completely dry, you can apply Pour-N-Restore to the embedded oil stain following the directions on the bottle.